V2

GS Limo

Suppliers of 

 

Ţ Dunebuggy kits and all accessories

Ţ VW engine upright cooling systems

Ţ Subaru engine install & components

 

 Upright cooling kits

 Subaru engine install

SUPA SUMP

 

The Supa Sump is 2'' shorter than stock but has the same capacity and oil level, the oil pick up is also shortened  2'' factory oil baffle plate and oil drain  tube remain in the stock location there is no modification required to the dip stick tube, the sump fastens back onto the engine using the standard bolts.

 

The factory baffle plate in the sump is a much needed item though some aftermarket sumps do not have them, some suppliers will say you don't need them or a couple of  plates welded in do the same job. Here is part of a tech sheet put out when the EJ series was developed LINK

 

For those that wish to do some work themselves the 'new sump box' is available on its own, this way you can weld it onto your own existing sump and save time and money

 

The Supa Sump is suitable for all applications including low street VWs, offroad dune buggies, baja bug’s, sand rails and  kit cars.

HEADERS

 

These have been designed for a Dunebuggy or Baja Bug.

The headers and flanges are made from stainless steel, you supply and fit your own muffler to suit your bar work, they can be supplied with a flange for a Subaru turbo.

ADAPTOR PLATE AND FLYWHEEL

 

The  adaptor plate and flywheel are made from steel, the flywheel is one piece construction and available in 215 mm and 228 mm clutch size, there supplied with all the needed hardware.

SHORT HEADERS

 

The short stainless steel headers allow you to make up your own exhaust system, they can be fitted facing forwards or backwards to suit your needs.

REVERCE DIRECTIONAL INLET MANIFOLD

 

This reverse's the throttle body direction away from the baulk head when there is interference, it is also available with an offset if you have a plastic remote AFS, because of it’s offset it position’s the AFS and air cleaner in a much better location away from the rear wheel and baulk head.

LONG RANGE ALLOY FUEL TANK

 

The tank was designed to make the Subaru engine install easier, it is baffled and a Subaru high pressure fuel pump/fuel gauge sender unit can be installed that already has the fuel line tails installed, the filler neck location can be supplied to suit different needs, it’s capacity is close to 50 liter’s and there is a drain plug installed, it will only fit a Beetle - Baja - Dune buggy or Country buggy that has a 2’’or 3’’ lift kit fitted.

Subaru Install products

SOLID WATER LINES

 

Alloy tube water lines left and right side and securing clips, these run on the out side of the body front to rear just below the fiber glass lip and connect the radiator to the engine’s water inlet/outlet, the attachment clips have rubber sleeve's to stop noise, vibration and heat contacting the body    

SUBARU GAUGE CLUSTER

 

The Subaru gauge cluster (exchange) is recalibrated and is supplied with a new speedo cable and new fascia cover. The cluster has new laser cut gears installed and a new spring and is also serviced, it has all the gauges and warning lights needed and also the important vehicle speed sensor which works with the factory ECU

HEAVEY DUTY GEARBOX CRADLE

 

This cradle is much stronger than the standard VW one and comes with a rubber lined gearbox strap, lower bar work can be attached to it and a skid plate, also hangers from above can attached to it to stop the folks from moving/bending

Page under construction

REAR DISC BRAKES

 

Rear disc brakes featuring a billet alloy attachment brackets, Porsche 914 rota’s and VW Mk 4 alloy calipers. Available as a complete kit or parts.

 

Here are some install pics on a Dunebuggy, a model of caliper is available with the handbrake cable located above—-good for a buggy or Baja pic’s

 

Here is a link to some install pics on a Beetle, a Golf caliper is used with the handbrake cable located below in the normal position  pics

 

*  Information

 

*  V2

 

*  V2 Sandshark

 

*  Kits & accessories

 

 

FRONT DISC BRAKES FOR A 181 ‘THING’.

 

Front disc brakes featuring a billet alloy attachment brackets for fitting a VW Beetle or Ghia front caliper’s and disc’s to a 181 ‘Thing’ front spindle. Available as a complete kit or parts. pics

FLIP UP AERO STYLE LOCKING FUEL FILLER CAP

 

Something that has been needed for a long time, designed just for a dune buggy, a flush flip up locking fuel cap a new lower alloy dish and a tank breather in the cap.

 

It unlocks with a key and flips up, press the cap back down and it self locks and is 100% weather proof, the OD of the top outer ring is only 4-1/2", it’s been designed for street and off road use with an over sized 1/2'' drain tube located in the dish which will get rid of fuel spill-water-dust-dirt-sand-mud that may collect in there.

 

It is fitted by cutting a hole and sandwiching the fiberglass between the 2 parts, a fuel hose connects to the neck in the dish and to the fuel tank neck, comes with a section of 2’’ ID fuel hose, 2 clips, instructions and a stick on template to use for cutting the hole location. pic